Written report
Photos and notes on every component we tested
Sump Pump Inspection Naples FL You Can Schedule Today
A sump pump inspection Naples FL is the fastest way to find a failing float switch, a clogged discharge line, or a cracked sump basin before water backs into your crawl space. We test submersible and pedestal pumps, check valves, and battery backup systems for homeowners across Collier County, then hand you a plain-English report the same day.
- Float switch
- Check valve
- Backup battery
- Written scope firstFlat price before we start
- Full cycle testPump runs three times before we leave
- Parts on the truckPumps, floats, valves, batteries
- Pit left cleanDebris removed, basin rinsed
What Is Included in a Sump Pump Inspection
Every inspection covers the full pump system, not just the motor. We test the pump, float switch, check valve, discharge line, basin, and any backup or alarm. If we find a part that needs replacing, we quote it upfront and can usually handle it the same visit. Here is what you get.
- Pump Cycle TestWe add water to the sump basin and cycle the pump 10 to 15 times. We time how long it takes to clear the pit, listen for grinding or rattling, and clamp a meter on the circuit to check amp draw against the motor rating.
- Float Switch CheckThe float switch is the most common failure point. We check the travel, look for cracks or debris, and confirm it trips the pump at the right water level. A sticking float is why most pumps will not turn on.
- Check Valve and Discharge LineWe inspect the check valve for backflow and follow the discharge line to its termination. A clogged discharge line or a valve that leaks back makes the pump short-cycle and burn out early. We rod or replace as needed.
- Basin and Pit ConditionWe look at the sump basin liner for cracks, check the pit for silt and gravel buildup, and confirm the lid seals. A cracked basin lets groundwater seep around the pump and reduces how much water the pit can hold.
- Backup and Alarm TestIf you have a battery backup system, water-powered backup pump, or sump pump alarm, we test each one. We load-test the battery, check the charger, and confirm the backup moves water when the primary is disabled.
- Written ReportYou get a summary with photos of every component, notes on what passed and what needs attention, and upfront pricing on any repair. The report is yours to keep and useful for insurance or a home sale.
Sump Pump Inspection for Homes
We inspect sump pumps in Naples homes with crawl spaces, basements, and shallow pits. You get a clear report on the pump, float, valve, and backup before the next storm.
- Pump will not turn on
- Pit refills too fast
- Backup battery weak
- Discharge line clogged
Sump Pump Inspection for Businesses
We inspect sump pumps in Naples commercial buildings where a failed pump means lost inventory or a closed floor. You get documentation you can file with your maintenance records.
- RetailProtect stockrooms and lower-level storage from water
- RestaurantKeep walk-in coolers and prep areas dry
- OfficeCheck pits in below-grade utility rooms
- WarehouseTest pumps that handle loading-dock runoff
What a Sump Pump Inspection Naples FL Covers
A sump pump inspection Naples FL is a hands-on evaluation of the entire discharge path, not just a glance at the pump. We pull the lid, check the float switch travel, cycle the pump with water, and watch how fast the sump basin refills. We inspect the check valve for backflow, rod the discharge line for clogs, and test any battery backup system under load. If the pump short-cycles, runs constantly, or won't turn on, we find out why before it becomes an emergency.
Naples sits on a high water table, and from June through October the afternoon storms dump two inches in an hour. That is when a failed float switch turns a dry crawl space into a wet one. If you are buying a home, a home sale sump pump inspection Naples Florida gives you leverage and a repair list. If you are prepping for storm season, a pre-hurricane sump pump inspection Naples FL is cheap insurance. Either way, you get a clear picture of what will hold and what will not.
We test the whole discharge path, not just the motor.
How Our Sump Pump Inspection Works
We schedule in two-hour windows, arrive with test water and meters, and walk you through what we find. Most inspections take 60 to 90 minutes depending on how many pumps and pits your property has.
Book the Visit
Call or book online and tell us what the pump is doing, or not doing. We ask about the pump brand, age, and whether you have a battery backup system. You get a two-hour arrival window, and we text when the technician is on the way. Same-day slots are usually open for active leaks or a pump that has stopped running.
Test the Pump
We pour water into the sump basin and watch the float switch trip the pump. We time how long the pump takes to clear the pit, listen for grinding or rattling, and clamp a meter on the circuit to check amp draw. A healthy submersible sump pump clears a standard basin in under 30 seconds.
Inspect the Discharge Path
We follow the discharge line from the check valve to the exterior termination. We look for a clogged discharge line, a stuck check valve, or a pipe that drains too close to the foundation. In freeze-prone weeks, we also check for a frozen discharge line, which is rare here but happens in North Naples after a hard January cold snap.
Check Backup and Alarm
If you have a battery backup system or water-powered backup pump, we test it with the primary pump disabled. We check the battery voltage, the charger indicator, and the float on the backup. We also test the sump pump alarm so you know it will sound before water reaches the floor.
Review the Findings
We hand you a written summary with photos, note which parts are fine, which are near end of life, and which need replacement now. You get upfront pricing on any repair before we touch a tool. If everything passes, we tell you that too, and you are set for the season.
Tools and Methods We Use on Every Inspection
Clamp meter
Measures amp draw on the pump circuit so we can compare it to the motor rating and spot a pump that is working too hard.
Battery load tester
Puts a real load on the backup battery to confirm it holds voltage and will run the backup pump during an outage.
Discharge line rod
Clears clogs from the PVC discharge pipe without cutting it open when the blockage is accessible from the termination.
Test water and bucket
Lets us cycle the pump repeatedly and time how fast the sump basin clears under controlled conditions.
Float switch tester
Confirms the switch trips at the correct water level and returns to the off position without sticking.
Inspection camera
Looks inside the sump basin and discharge line when the clog or crack is not visible from the top.
Zoeller and Wayne replacement parts
Common float switches, check valves, and gaskets kept on the truck so repairs can happen the same visit.
Cycle testing
We fill the sump basin and let the pump run through 10 to 15 cycles. This reveals short-cycling, a float that sticks, or a motor that hesitates under load. It is the fastest way to see how the pump behaves under real conditions.
When to Schedule a Sump Pump Inspection
You are buying a home in Naples with a crawl space or basement, and the seller has no pump service records.
We perform a home sale sump pump inspection Naples Florida that documents the pump brand, age, float switch condition, check valve, and discharge routing. You get photos and a repair list with pricing before your inspection period ends. You know exactly what you are buying, and you have leverage to negotiate repairs or a credit at closing.
It is May, and you want the pump ready before the June-through-October storm season starts.
We schedule a pre-hurricane sump pump inspection Naples FL that tests the pump, float, valve, and backup system. If the battery is weak or the float is sticking, we fix it now while the schedule is open. Your pump is storm-ready, and you avoid the rush of emergency calls that hits after the first big rain.
Your pump runs every few minutes, even when it has not rained.
We test the check valve for backflow and check the float height. A leaking valve or a float set too low is usually the cause. We replace the valve or re-set the float and re-test the cycle. The pump cycles normally again, your power bill drops, and the motor is not burning out from constant use.
You lost power during a storm and realized you have no backup pump.
We inspect the primary pump and pit, then quote a battery backup system or water-powered backup pump installation. We tie the backup into the same discharge line with its own check valve. The next outage does not leave your crawl space unprotected, and the backup runs automatically when the primary stops.
How Sump Pump Inspection Works in Naples
Naples has a high water table, and in coastal neighborhoods like Royal Harbor and Aqualane Shores the water table rises with the tide. That means a sump pit can refill even on a dry day, and a pump that cannot keep up will run constantly. Inland areas like Golden Gate and Lely Resort see more stormwater runoff from afternoon thunderstorms, which dump two inches in an hour during July and August. We size our inspection to your location: coastal homes get a closer look at the check valve and basin for tidal seepage, while inland homes get a discharge line check for yard debris and silt. We also follow Florida Building Code on discharge termination and NEC electrical code on the pump circuit. If you are scheduling a sump pump assessment Naples appointment in October, we will also check the backup battery before the cooler months, when power demand and storm outages can still hit. A professional sump pump inspection Naples should reflect your block, not a generic checklist.
- Old NaplesHistoric homes with shallow crawl spaces and older pits. We check for cracked basin liners and undersized pumps that cannot handle tidal groundwater.
- Pelican BayMany homes have enclosed lanais and low slabs. We confirm the discharge line terminates far enough from the foundation to avoid re-entry.
- Golden GateInland lots with more runoff from afternoon storms. We check the discharge line for silt and confirm the pit refill rate matches the pump capacity.
- Vanderbilt BeachCoastal properties where the water table moves with the tide. We test the check valve closely for backflow and check the float height.
- East NaplesA mix of older and newer construction. We look at the sump basin condition and whether the pump circuit meets NEC electrical code.
- High water table near the coastPits refill faster, so the pump cycles more often. We check the check valve and float height to make sure the pump is not short-cycling and burning out early.
From problem to finished result.
Short-Cycling Pump in Old Naples
BeforeA homeowner in Old Naples called because the pump ran every three minutes, even on dry days. The pit was refilling from a leaking check valve, and the pump had been short-cycling for weeks. The motor was hot to the touch and the float switch was sticking.
AfterWe replaced the check valve and float switch, re-set the float height, and cycled the pump 12 times. The pit now clears in under 30 seconds and stays empty between storms. Amp draw dropped back to the motor rating, and the pump no longer runs constantly.
We recommended an annual inspection each May and a basin cleaning every two years to keep silt off the float. The homeowner also added a sump pump alarm for early warning.
Dead Backup Battery in Pelican Bay
BeforeA Pelican Bay homeowner had a battery backup system installed five years ago and never tested it. During a storm outage, the backup did not run and water reached the lanai. The battery read 11.8 volts at rest and failed immediately under load.
AfterWe replaced the battery, tested the charger, and ran the backup pump with the primary disabled. The backup now moves water for over 40 minutes on battery power. We also replaced the check valve on the backup line, which was leaking back into the pit.
We set a reminder to load-test the battery every six months and replace it every four years. The homeowner now checks the charger indicator light monthly.
Clogged Discharge Line in Golden Gate
BeforeA Golden Gate home had a pump that ran but never cleared the pit. The discharge line was clogged with yard debris and silt, so water cycled right back into the basin. The pump had overheated twice and tripped the breaker.
AfterWe rodded the discharge line, replaced a cracked section of PVC discharge pipe, and re-routed the termination away from the foundation. The pump now clears the pit in 25 seconds, and the breaker has not tripped since. We also cleaned the basin and checked the float travel.
We recommended checking the exterior discharge outlet each spring and keeping mulch and leaves away from the termination. An annual inspection keeps the line clear.
Sump Pump Problems We Find and Fix in Naples
Most sump pump failures start small: a float that sticks, a valve that leaks back, a discharge line that clogs with yard debris. Left alone, they turn into a flooded crawl space or a wet basement floor. These are the problems our inspection catches.
Sump pump running constantly
We test the check valve for backflow and check the float height. If the valve is leaking, we replace it with a new one and re-set the float so the pump cycles normally instead of running nonstop. A pump that never shuts off burns out its motor in weeks and spikes your power bill. It usually means a leaking check valve or a float set too low.
Sump pump not turning on
We test the float switch travel and the pump circuit. If the switch is cracked or stuck, we replace it. If the circuit is the issue, we check it against NEC electrical code and correct the wiring. A dead pump during a storm lets the pit overflow within minutes, sending water into your crawl space or basement. The cause is usually a failed float switch or a tripped circuit.
Clogged discharge line
We rod the discharge line from the check valve to the exterior termination. If the clog is severe or the pipe is cracked, we replace the section with new PVC discharge pipe and re-test the flow. When the discharge line clogs, the pump runs but the pit never clears. Water backs up, the pump overheats, and you are left with a flooded floor and a burned-out motor.
Backup pump failure during power outage
We load-test the battery, check the charger, and run the backup pump with the primary disabled. If the battery reads under 12.4 volts or is more than four years old, we replace it so the backup runs when the power drops. A battery backup system that has not been load-tested can fail the one time you need it. Old batteries lose capacity, and chargers stop working without any warning light.
Cracked sump basin
We inspect the basin liner for cracks and seal or replace it. If the pit itself has shifted, we re-line it and seal the joints so the pump draws from the pit, not the surrounding soil. A cracked basin lets groundwater seep in around the pump, so the pit never fully drains. Over time the pump runs longer, the motor wears out, and the pit walls can shift.
We find the failing part before it floods your floor.
Catch Failures Early
Most pumps we test fail on the float switch or check valve, not the motor. During a professional sump pump inspection Naples, we cycle the pump 10 to 15 times and watch for a float that sticks, a valve that leaks back, or a motor that draws high amps. Finding those parts early turns a $600 flood cleanup into a $95 switch replacement.
Protect Crawl Spaces
In East Naples and Golden Gate, many homes sit on crawl spaces with a sump pit cut into the slab. When the pump quits, water wicks into floor joists and insulation within hours. Our inspection measures the refill rate of the sump pit and confirms the pump can keep up with a 2-inch rain event, which is common here in August.
Verify Backup Power
A battery backup system only helps if the battery holds a charge. We load-test the battery, check the charger, and confirm the backup pump moves water when the primary is unplugged. If the battery is more than four years old or reads under 12.4 volts, we tell you straight instead of letting it fail during a hurricane outage.
Document for a Sale
Realtors in Port Royal and Aqualane Shores order our sump pump inspection service Naples FL before closing because buyers ask about water intrusion. You get photos of the sump basin, the discharge line routing, and a written summary of every component we tested. That paperwork answers buyer questions and shortens the inspection period.
Sump Pump Inspection Cost in Naples
Typical 2026 pricing in this area runs $95 to $185 for a single-pump home and $150 to $260 when you have a primary pump plus a battery backup system. Crawl space pits with limited access, a second sump basin, or a pump that needs to be pulled for a bench test add to the time. We quote the price before we start, and if we find a repair you approve, we credit the inspection fee toward the work. That keeps the visit worthwhile whether the pump passes or fails.
What your estimate is based on
- Number of pumpsA single primary pump takes less time than a primary plus a battery backup system or water-powered backup pump. Each additional pump adds a cycle test and a load test, which adds 20 to 30 minutes to the visit.
- Pit accessibilityA sump pit under a sealed lid in a finished space takes longer to access than an open pit in a crawl space. Tight clearance means we may need to move stored items or work from a different angle.
- Discharge line lengthA long discharge line with multiple fittings takes more time to inspect and rod. If the line runs under a slab or through a wall, we may use an inspection camera to check for clogs and cracks.
- Pump conditionA pump that cycles normally is a quick test. A pump that will not turn on, runs constantly, or makes loud noise takes longer to diagnose because we have to isolate the float switch, check valve, and motor separately.
- Basin and pit conditionA cracked sump basin or a pit full of silt and gravel adds cleaning and inspection time. If the basin needs to be re-lined or replaced, that becomes a separate repair with its own price.
- Backup system typeA battery backup system needs a load test and a charger check. A water-powered backup pump needs a flow test. Each type has its own test procedure, and the time difference shows up in the price.
$95 - $260 depending on pump count and system type The inspection fee is credited toward any repair you approve the same visit, so you are not paying twice. More importantly, catching a $95 float switch before it floods a crawl space saves thousands in water damage and mold cleanup.
What you receive
Clear records you can keep and share.
Repair list
Upfront pricing on any part that needs replacing
Test results
Cycle times, amp draw, and battery voltage
What Naples Homeowners Should Know About Sump Pumps
A sump pump inspection checks the whole system, not just the motor. Most failures we find in Naples are float switches and check valves, not burned-out pumps.
Float switches fail first
The float switch is the most common reason a pump will not turn on. It sticks, cracks, or catches debris. Replacing it is far cheaper than replacing the pump.
Check valves leak back
A check valve that leaks lets water drain back into the pit and makes the pump short-cycle. You will hear the pump run every few minutes even when it is dry outside.
Backups need load tests
A backup battery can read fine at rest and still fail under load. We test it with the primary pump disabled so you know it will run during an outage.
Sump pump service across Naples
- Old Naples
- Park Shore
- Coquina Sands
- Moorings
- Naples Park
- Pelican Bay
- Vanderbilt Beach
- North Naples
- Golden Gate
- East Naples
- Lely Resort
- Naples Manor
- Bayshore
- Royal Harbor
Outside these areas? Call and ask, we may still cover you. +12395220157
What Naples Homeowners Say
A full inspection covers the pump, float switch, check valve, discharge line, sump basin, and any backup system. We cycle the pump with water, time how long it takes to clear the pit, check amp draw, and test the alarm. You get a written summary with photos and upfront pricing on any repair we recommend. Most inspections take 60 to 90 minutes.
Typical 2026 pricing in this area runs $95 to $185 for a single-pump home, and $150 to $260 if you have a primary pump plus a battery backup system. Crawl space pits with limited access or a second sump basin add to the time. We quote the price before we start, and the inspection fee is credited toward any repair we do the same visit.
Once a year, ideally in May before storm season, and again if the pump has been sitting unused for months. If your pump is more than five years old or runs on a float switch that has never been replaced, twice a year is smart. A sump pump assessment Naples homeowners schedule annually catches most failures before the first big rain.
Yes. We perform home sale sump pump inspection Naples Florida appointments for buyers, sellers, and realtors. We document the pump brand, age, discharge routing, and any defects with photos, then give you a repair list with pricing. That report answers buyer questions and helps you negotiate before the inspection period closes.
Book Your Sump Pump Inspection Naples FL Today
Do not wait for the next storm to find out your pump is dead. Call Naples Sump Pump Pros, and we will test the pump, float switch, check valve, and backup system, then hand you a written report the same day. Upfront pricing before any repair.
Call Naples Sump Pump Pros
Call us at +1 239-522-0157 or email [email protected]. We answer the phone during business hours and dispatch emergency calls after hours. Same-day estimates are available for most of Naples and Collier County. If you are not sure whether you need a repair or a full install, describe what you are seeing and we will tell you straight.